Qingdao Shuodi Environmental Protection Technology Co., Ltd. is a Chinese manufacturer specializing in the production of ammonia nitrogen remover. Zoetis has been working on the research of ammonia nitrogen remover for many years. Scope of application of ammonia nitrogen remover 1. Purification of urban domestic sewage; 2. Applicable to various industrial wastewater, including ink, packaging and printing, auto parts, machinery, painting, surface treatment, paint, paint, electroplating, papermaking, food, printing and dyeing , bleaching and dyeing, tanning and other wastewater treatment processes.
Qingdao Shuodi Environmental Protection Technology Co., Ltd. is a Chinese supplier specializing in the manufacture of ammonia nitrogen remover. Ammonia nitrogen refers to nitrogen that exists in the form of free (NH3) and ammonium ions (NH4+) in water. After most wastewater is treated, ammonia nitrogen will not be too high, most of which are around 20-80mg/L. To reduce this part of ammonia nitrogen If it is less than 10mg/L or even lower, ammonia nitrogen treatment agents must be added for degradation, so that ammonia nitrogen can meet the national emission standards. This product is a truly efficient and environmentally friendly ammonia nitrogen treatment agent. After dissolving in water, it can generate new ecological oxygen and convert ammonia nitrogen into ammonia gas for removal. The reaction efficiency is high, and the ammonia nitrogen in the water body can be quickly and completely removed.
1. The reaction speed is fast, and the reaction process can be completed in about 10 minutes;
2. The removal efficiency is high, compared with other ammonia nitrogen removal agents, it has a higher dosage
Less, high solubility, great removal effect;
3. Easy to add and use, good operability;
4. It also has the functions of breaking cyanide, breaking heavy metals, and decolorizing sewage.
Reduce some auxiliary functions such as COD from time to time;
5. The medicament solution is alkaline, and it can also be used for pH adjustment to save the cost of alkali consumption.
Project | Standard |
Exterior | off-white particles |
content | ≥99% |
Density (g/cm3) | / |
Oxidation component | ≥60% |
sucking ingredients | ≥30% |
Catalyst | Greater than or equal to 5% |
pH value | Alkaline |
Before normal use, you can conduct a small test in the laboratory to determine the use effect and dosage. The method is as follows: 1) Measure 200ml of waste water;
2) Sequentially add ammonia nitrogen remover (such as 100ppm, 200ppm, etc.);
3) Stir for about 10 minutes to make the medicine fully reflect
4) Determination of residual ammonia nitrogen value in water
[Pharmaceutical configuration]: For engineering use, it can be configured as a 10% solution, which is added through a metering pump
[Dosage amount]: The general situation is as follows. Adding 1kg of this product per ton of wastewater can reduce the ammonia nitrogen value by about 100mg/L; the specific dosage should be calculated according to the ammonia nitrogen content in the wastewater or determined through a small experiment.
[Conditions of use]: It is suitable for the pH range of 1-12. It is recommended to add it at the back end of biochemical treatment, and the reaction time is about 10 minutes.
d. Stir for about 1-2 minutes to allow the drug to fully react
e. Add appropriate amount of coagulant and flocculant (PAM);
f. Check the water quality after coagulation and sedimentation.
(2) On-site use;
a. COD remover dosing point
The reaction of the COD remover is very fast, and the reaction can be completed in about 2-3 minutes. It can directly treat the waste water with excessive COD. Therefore, after the sedimentation tank, it can be added to the Desand filter or the callback tank. In order to ensure the complete reaction, Aeration or stirring is required.
b. Optimal dosage
Since the COD value of wastewater (raw water) varies, the dosage will vary according to the level of COD; the optimal dosage of wastewater is recommended to be determined through experiments, and finally adjusted during use.
Dosage amount (ppm) | / | 100 | 200 | 300 | 400 | 500 |
---|---|---|---|---|---|---|
Residual ammonia nitrogen (mg/L) | 49.5 | 37.6 | 29.3 | 18.5 | 11.2 | 8.5 |
Ammonia nitrogen remover is slightly corrosive, the operator can code the protective equipment to ensure the safety of feeding, and it is strictly forbidden to put it in a humid, hot, exposed to the sun or rain;
Ammonia nitrogen remover should not be stored for a long time, and should be handled with care when loading and unloading.
Specification of ammonia nitrogen remover: 25kg/bag